1、电源电压：110V/220V 2、主轴驱动率：180W 3、主轴转速：300-3000rpm 4、X轴滑板行程：210mm 5、Y轴滑板行程：110mm 6、Z轴滑板行程：90mm 7、步电机分辨率：0.0025mm 8、步电机定位度：0.01mm 9、大切割深度：50mm 10、作台旋转：360°±0.5° 11、载物板：80mm×25.4mm 12、载体盘：Φ80mm 冲击试验低温槽 型号:HAD-DWC-40 型号 HAD-DWC-40 HAD-DWC-60A HAD-DWC-80 HAD-DWC-100 温度范围 30～-40℃ 30～-60℃ 30～-80℃ 30～-100℃ 控温度 ±0.5℃ 作槽 120mm*120mm*70mm（可根据用户要求定做） 可装式样数量 ＞60（仅对金属夏比缺口冲击试验） 作介质 无水乙醇（酒槽） 电源供电 220V～240V,50HZ 外形尺寸 910mm*500mm*870mm 净重 约90kg HAD-DWC-40型冲击试验低温槽操作简单方便，无化学污染、无噪音、无振动、无磨损、体积小、重量轻、操作简单、控制度、可连续作等点，是金属材料低温冲击试验中的理想的试样冷却、保温设备。DWC型冲击试验低温槽同时亦可用于其他低温检测和试验作。本冲击试验低温槽是我公司根据GB/T229-2007《金属夏比缺口冲击试验方法》中对低温装置的要求而新研制开发的压缩机制冷设备。 5.自动压样机/ 型号:HAD-600KN 我公司的压样机是X射线荧光光谱仪的配套设备。HAD-400KN，HAD-600KN型压样机采用内模压样方式，操作方便、效率、性能稳定可靠。
产品结构点 Characteristics of the Products ●内模式压样，压头行程100毫米。可用于硼酸、钢环、铝杯、塑环等各类压样方式，适用范围广，作稳定。 Adopted internal mould sample-press, pressure head travel is 100 mm. The products can be used for various kinds of sample-pressing methods such as boric acid, steel ring, aluminum cup, plastic ring etc., with characteristics of broad scope of application and stable working.
●有的缓加压、慢退模程序更有利于保证压样合格率、提压样样量。 With specific programs of slow pressurization and slow mould-release, the products are favorable to ensure acceptance rate of sample-press, improve sample quality of sample-press.
●别的集成液压管道模块不仅使组装更加方便，而且减少了漏油机会。 With integrated hydraulic pipe block being specially designed, it not only makes assembling easier, but also reduces the chance of oil leak.
●加厚的油箱盖板使油泵和电磁阀的动作噪音更小。 With thickening oil-tank cover-board, it makes acting noise of oil pump and solenoid valve smaller.
●采用由可控硅集成的固态模块替代传统的接触器避免了由于电机频繁启动而引起的各类故障，有效提了该分的使用寿命。 Adopted solid-state block of integrated silicon controlled to replace traditional contactor, it avoids various kinds of troubles caused by frequent starting of motor and efficiently increases service life of this section.
●继电器控制分采用印刷板焊接结构，减少了控制箱的接线，提了电器控制的可靠性。 The Control section of relay is adopted the welding structure of printed circuit board, it reduces wiring of control box, improves reliability of electric control.
●控制电源采用低压24V，作更加安可靠。 Control power source is fully adopted low-voltage of 24V, which makes work safer and more reliable.
●结构紧凑，占地面积小。 With compacting structure, small floor space 参数
大压片压力60tf (吨)
模具 硼酸、钢环、铝杯和塑料环
压头大行程100mm
压片保压时间0~999 秒
供电电源380V
额定率1.3kw
外型尺寸1180x720x530mm
净重420Kg | 
